Читать реферат по английскому: "Silicon Essay Research Paper Silicon" Страница 1

(Назад) (Cкачать работу)

Silicon Essay, Research Paper

Silicon

Silicon is the raw material most often used in integrated circuit (IC)

fabrication. It is the second most abundant substance on the earth. It is

extracted from rocks and common beach sand and put through an exhaustive

purification process. In this form, silicon is the purist industrial substance

that man produces, with impurities comprising less than one part in a billion.

That is the equivalent of one tennis ball in a string of golf balls stretching

from the earth to the moon.

Semiconductors are usually materials which have energy-band gaps smaller

than 2eV. An important property of semiconductors is the ability to change

their resistivity over several orders of magnitude by doping. Semiconductors

have electrical resistivities between 10-5 and 107 ohms. Semiconductors can be

crystalline or amorphous. Elemental semiconductors are simple-element

semiconductor materials such as silicon or germanium.

Silicon is the most common semiconductor material used today. It is used

for diodes, transistors, integrated circuits, memories, infrared detection and

lenses, light-emitting diodes (LED), photosensors, strain gages, solar cells,

charge transfer devices, radiation detectors and a variety of other devices.

Silicon belongs to the group IV in the periodic table. It is a grey brittle

material with a diamond cubic structure. Silicon is conventionally doped with

Phosphorus, Arsenic and Antimony and Boron, Aluminum, and Gallium acceptors.

The energy gap of silicon is 1.1 eV. This value permits the operation of

silicon semiconductors devices at higher temperatures than germanium.

Now I will give you some brief history of the evolution of electronics

which will help you understand more about semiconductors and the silicon chip.

In the early 1900’s before integrated circuits and silicon chips were invented,

computers and radios were made with vacuum tubes. The vacuum tube was invented

in 1906 by Dr.Lee DeForest. Throughout the first half of the 20th century,

vacuum tubes were used to conduct, modulate and amplify electrical signals.

They made possible a variety of new products including the radio and the

computer. However vacuum tubes had some inherent problems. They were bulky,

delicate and expensive, consumed a great deal of power, took time to warm up,

got very hot, and eventually burned out. The first digital computer contained

18,000 vacuum tubes, weighed 50 tins, and required 140 kilowatts of power.

By the 1930’s, researchers at the Bell Telephone Laboratories were looking

for a replacement for the vacuum tube. They began studying the electrical

properties of semiconductors which are non-metallic substances, such as silicon,

that are neither conductors of electricity, like metal, nor insulators like wood,

but whose electrical properties lie between these extremes. By 1947 the

transistor was invented. The Bell Labs research team sought a way of directly

altering the electrical properties of semiconductor material. They learned they

could change and control these properties by “doping” the semiconductor, or

infusing it with selected elements, heated to a gaseous phase. When the

semiconductor was also heated, atoms from the gases would seep into it and

modify its pure, crystal structure by displacing some atoms. Because these

dopant atoms had different amount of electrons than the semiconductor atoms,

they formed conductive paths. If the dopant atoms had more electrons than the

semiconductor atoms, the doped regions were called n-type to signify and excess

of negative charge. Less electrons, or an excess of positive charge, created p-

type regions. By allowing this dopant to take place in carefully delineated

areas on the surface of the semiconductor, p-type regions could be created

within n-type regions, and vice-versa. The transistor was much smaller than the

vacuum tube, did not get very hot, and did not require a headed filament that

would eventually burn out.

Finally in 1958, integrated circuits were invented. By the mid 1950’s, the

first commercial transistors were being shipped. However research continued.

The scientist began to think that if one transistor could be built within one

solid piece of semiconductor material, why not multiple transistors or even an

entire circuit. With in a few years this speculation became one solid piece of

material. These integrated circuits(ICs) reduced the number of electrical

interconnections required in a piece of electronic equipment, thus increasing

reliability and speed. In contrast, the first digital electronic computer built

with 18,000 vacuum tubes and weighed 50 tons, cost about 1 million, required 140

kilowatts of power, and occupied an entire room. Today, a complete computer,

fabricated within a single piece of silicon the size of a child’s fingernail,

cost only about $10.00.

Now I will tell you the method of how the integrated circuits and the

silicon chip is formed. Before the IC is actually created a large scale drawing,

about 400 times larger than the actual size is created. It takes approximately

one year to create an integrated circuit. Then they have to make a mask.

Depending on the level of complexity, an IC will require from 5 to 18 different

glass masks, or “work plates” to create the layers of circuit patterns that must

be transferred to the

Похожие работы